| You are here : Homepage > Products |
|
|
| For sale |
| List Price : |
767.10 US |
| Our Price : |
673.00 US |
| Free shipping in Canada * |
|  |
 |
| Aviom AV-P2 |
|
Aviom AV-P2
The AV-P2 Output Module provides up to two channels of analog outputs from a Pro16 A-Net digital audio stream. The analog output level for each channel is set with front-panel DIP switches.
AV-P2 modules can be connected in any combination of serial or parallel connections, using Pro16
A-Net Distributors. There is no limit to the number of devices that can be daisy chained, or to the number of parallel splits in a single system.
Each AV-P2 receives a 16-channel A-Net stream originating at a Pro16 input module, console interface card, or Pro64™ audio network (via the ASI A-Net Systems Interface module).
A front-panel rotary switch allows the output to be set to any one of those 16 channels. If the selected channel is part of a stereo pair (set at the input module), the left and right channels are automatically routed to the left and right outputs on the AV-P2. If the selected channel is not part of a stereo pair, the channel's audio is routed to both the left and right outputs.
Audio is distributed to the AV-P2 over standard Cat-5e cables, using Aviom's A-Net digital audio protocol. A-Net supports plug-and-play installation, real-time distribution with sub-millisecond latency, and long cable runs up to 500ft/150m. Power can be supplied to the AV-P2 with an external DC power supply or over the Cat-5e cable (with an A-Net Distributor). Additionally, Pro16 A-Net audio streams can be transmitted over single- or multi-mode fiber optics using certain standard third-party media converters.
The AV-P2 has reversible mounting flanges. Two AV-P2 modules can be mounted side by side on a standard 1U rack tray. The AV-P2 is compatible with all Pro16 Series products.
Features
Provides 1- or 2-channel analog output from a Pro16 A-Net streamIndependently selectable output levels for left and right channels48kHz, 24-bit D/A convertersOptional power over Cat-5e using a Pro16 A-Net DistributorSimple plug-and-play installationSecure set- and-forget channel configurationReversible mounting flanges
Specifications
Audio Outputs:
2, impedance balanced line-level
5.0 mm Euroblock connectors, female, panel-mount
2 male Euroblock connectors supplied in box
Screw terminals: Audio +; Audio -; Ground
Channel Selection: 16-position rotary switch
D/A Conversion: 48kHz, 24-bit
Output Levels:
Variable: +4dBu to -31dBu in 1.5dB increments
6-position DIP switch, per channel
Indicators: LEDs; red: Power, green: A-Net Active, yellow: Stereo Pair
Output Impedance: 100 ohms
Signal to Noise: (unweighted)
93dB typical, A/D to D/A
Measured from AN-16/i Input Module to AV-P2
Freq. Response: 4Hz-22kHz +0.2dB/-3dB
THD +N: -93dB at -10dBFS
Crosstalk: -85dB at 1kHz
Bit Error Rate (BER): 10-12
Digital Connections: A-Net In: 1; A-Net Out: 1; RJ45 connectors
Pro16 A-NetŪ: Uses unshielded Cat-5e UTP (or better) cable
Latency: <0.880 msec (measured from analog input to analog output)
Power Supply: External, DC, universal switching type
Input Voltage : 100-240 volts, 50/60Hz, 30VA
Output Voltage : 18-24 VDC, 0.5 amp
Plug Size : 2 mm, locking, center pin hot
Dimensions: 7.45" (189.2 mm) wide x 7" (177.8 mm) deep; 1U high
Weight: 3.4 lbs (1.54 kg)
|
|
|
Studio Economik UA Apollo NEWS! We are placing the 1rst order for UA Apollo right now, available end February. Limited quantity available on first shipment. Pre-orders available. Please contact us to get yours!
|
