| You are here : Homepage > Products |
|
|
| For sale |
| List Price : |
2127.42 US |
| Our Price : |
1737.74 US |
| Free shipping in Canada * |
|  |
 |
| QSC RMX5050 |
|
QSC RMX5050
QSC's RMX 5050 power amplifier represents the state-of-the-art in professional quality performance at an affordable price. Perfectly suited for a wide range of sound reinforcement applications including professional touring, performing musicians, and mobile entertainers, the RMX 5050 is optimized to deliver high levels of sustained power, extraordinary audio performance and road-proven reliability.
Like its smaller sibling (the RMX 4050HD), the RMX 5050 features a three-tier, Class H design. The RMX 5050 is extremely efficient at real world power levels. Less AC current is wasted and more goes into producing useful audio power. The RMX 5050 uses the best available component upgrades to increase peak power by 25% over the RMX 4050HD.
Like all RMX amps, the RMX 5050 features balanced 1/4" TRS, XLR and barrier strip inputs, binding posts and Neutrik Speakon® outputs, front-mounted gain controls, plus signal and clip LED indicators to monitor performance.
Features
The new flagship of the RMX line, the RMX 5050 provides extremely high power and represents tremendous valueThe RMX 5050 provides advanced thermal performance, delivering higher continuous power in 2-ohms stereo or 4-ohms bridged applicationsDual mono, high current power supply for increased reliability and performance3RU chassis only 16" deepProfessional quality performance - incorporates road-proven QSC designsHigh-current toroidal transformers for greater two-ohm power and low noiseIndependent user-defeatable clip limiters reduce distortionSelectable low-frequency filters (30 Hz or 50 Hz) protect speakers and increase headroomBalanced 1/4" (6.3 mm) TRS, XLR, and barrier strip inputs for maximum flexibilityBinding post and Neutrik Speakon outputsFront mounted gain controls for easy accessSignal and Clip LED indicators to monitor performance
Specifications
SPECIFICATIONS
RMX 5050
STEREO MODE, Both Channels Driven
8 ohms
FTC 20 Hz - 20 kHz, 0.1% THD
EIA 1 kHz, 0.1% THD
1050 W
1100 W
4 ohms
FTC 20 Hz - 20 kHz, 0.1% THD
EIA 1 kHz, 0.1% THD
1600 W
1800 W
2 ohms
FTC 20 Hz-20 kHz 0.1% THD
EIA 1 kHz 1% THD
2000 W
2500 W
BRIDGE-MONO MODE
8 ohms
FTC 20 Hz-20 kHz 0.1% THD
EIA 1 kHz 0.1% THD
3200 W
3600 W
4 ohms
EIA 1 kHz 1% THD
5000 W
Distortion (SMPTE-IM)
Less than 0.02%
Distortion (Typical)
20 Hz - 20 kHz: 10 dB below rated power
1 kHz and below: full rated power
Less than 0.02%
Less than 0.02%
Frequency Response
20 Hz - 20 kHz, 8 ohms, LF filter bypassed, +0/-1 dB
5 Hz - 50 kHz, 8 ohms, LF filter bypassed, +0/-3 dB
Damping Factor
Greater than 250 @ 8 ohm
Noise (unweighted)
100 dB below rated output (20 Hz - 20 kHz, 8 ohm load)
Input Sensitivity
1.42 Vrms for 1050 watts into 8 ohms
Voltage Gain
64x (36 dB) for 8 ohm load
Input Impedance
20k ohm balanced, 10k ohm unbalanced
Controls Front:
Controls Rear:
AC power switch, Ch. 1 and Ch. 2 gain control
10-pole DIP switch featuring LF filter on/off, LF filter 30/50 Hz, Clip Limiter on/off controls for each channel and switches for selecting Stereo, Parallel, or Bridge mode. Push-button circuit breaker for each channel.
Indicators
Power-On: Green LED, Protect: Red LED
Signal -30dB: Yellow LED, Clip: Red LED
Connectors Input:
Connectors Output:
XLR female, TRS (1/4"), and barrier-strip screw terminals, each channel
Binding posts and Speakon® outputs (Ch. 1 Speakon wired for biamp)
Cooling
Continuously variable-speed fan, rear-to-front air flow
Amplifier Protection
Short circuit, open circuit, thermal, ultrasonic, and RF protection. Stable into reactive or mismatched loads
Load Protection
On/off muting, DC fault output crowbar
Power Requirements
100, 120 or 240 Volts AC (±10%) 50-60 Hz (factory configured)
120V models require 20 Amp service and are supplied with a NEMA 5-20 plug on the cordset.
Dimensions
19" (48.3 cm) wide, 5.25" (13.3 cm) tall, 15.9" (40.39 cm) overall depth
Weight
75 lbs (34.02 kg) net, 87 lbs (39.46 kg) shipping
|
|
|
Studio Economik UA Apollo NEWS! We are placing the 1rst order for UA Apollo right now, available end February. Limited quantity available on first shipment. Pre-orders available. Please contact us to get yours!
|
