MATFCCFFFFFF

Two Coaxial and Six Optical Modules
Combine coaxial antenna feeds with non-multiplexed optical inputs in one centralized RF distribution system.

Non-Multiplexed Fiber Connections
Each optical module provides two LC/APC inputs for single-mode fiber links.

Programmable Diversity Matrix
Configure eight zones into four outputs or divide the system into two groups of four zones feeding two outputs each.

Wideband RF Distribution
A broad RF operating range supports varied antenna distribution requirements.

Integrated Spectrum Analyzer
Inspect individual input modules before adding them to combined signals, or monitor the combined signals directly.

Independent Diversity-Path Gain
Adjust the A and B paths separately on each input module to balance incoming RF levels.

Smart Antenna Control
Control gain and filtering on compatible Wisycom LFA, ADFA and BFA antennas through the coaxial modules.

Configurable Antenna Power
Supply antenna booster power through the coaxial connections, with software-selectable High Boost available for both installed coaxial modules.

Colour Touchscreen Configuration
Access settings locally through the large touchscreen, buttons and encoder.

Ethernet Remote Management
Manage the matrix remotely through its Ethernet interface.

AC and DC Power Options
Integrate the system into installations using AC or DC supplies.

Configuration
Device Type: RF-over-fiber programmable matrix/combiner
Installed Coaxial Input Modules: 2, slots 1 and 2
Installed Optical Input Modules: 6 without multiplexers, slots 3–8
Optical Module Version: F
Maximum Optical Modules Supported: 6
Diversity Zones: Up to 8
Matrix Modes: 8 zones into 4 outputs, or dual 4 zones into 2 outputs
Fiber Requirement: Single-mode fiber for all optical links

RF Performance
Frequency Range: 170 MHz to 1260 MHz
Input Gain: −25 to +3 dB
Gain Adjustment Steps: 0.5 dB
Gain Regulation: Independent for each input module, A and B separately
Coaxial Module OIP3: +22 dBm typical at 3 dB gain
Optical Module OIP3: +18 dBm typical at 3 dB gain
Coaxial Amplifier Linearity: ±1 dB typical
Coaxial Module Noise Figure: 6 dB typical at 3 dB gain
Optical Module Noise Figure: 15 dB typical at 3 dB gain

Coaxial Connections and Antenna Power
Input Connectors per Coaxial Module: 2 × BNC female, A and B
Coaxial Impedance: 50 Ω
Output Connector Type: BNC female, 50 Ω
Maximum Coaxial RF Input Level: −10 dBm, with overload alarm
Antenna Booster Power: +12 V DC / 220 mA
High Boost Antenna Power: +12 V DC / 400 mA
High Boost Availability: Maximum 2 coaxial modules, software configurable
Smart Antenna Control: Gain and filter control for Wisycom LFA, ADFA and BFA through coaxial modules

Optical Connections and Performance
Input Connectors per Optical Module: 2 × LC/APC
Optical Wavelength Range: 1300–1650 nm
Optical Input Level: −6 dBm to +6 dBm (0.25 mW to 4 mW)
Absolute Maximum Optical Input Power: 10 mW; must not be exceeded

Spectrum Analyzer
Frequency Ranges: 170–260 MHz and 460–1260 MHz
Input Selection: Any one of the 8 input modules or combined signals, software selectable
Frequency Resolution: 50 kHz
Input Attenuator: 0 dB, 10 dB or 20 dB, software selectable
Timebase Accuracy: ±2.5 ppm maximum, 0–50 °C
Displayed Noise Level: −112 dBm typical
Displayed Amplitude Range: −117 dBm to −17 dBm
Maximum Input Level: −7 dBm with 20 dB input attenuation
Amplitude Accuracy: ±1.5 dB typical
Input IIP3: +15 dBm typical with 0 dB input attenuation
Sweep Speed: 70 MHz/s with diversity inputs
Full-Range Sweep Time: 13 seconds

Control and Display
Local Controls: Touchscreen menu, 2 buttons and encoder
Remote Interface: Ethernet 10/100 BaseT
Display Resolution: 1424 × 280 pixels
Display Colours: 16.7 million
USB Port: Reserved for future use

Power
AC Supply: 85–264 V AC, 47–63 Hz, 150 W maximum
Fuse: T3.15A
DC Supply: 10–28 V DC, 150 W maximum
Typical Consumption: 80 W with 2 coaxial modules in High Boost and 6 optical modules

Environmental and Physical
Operating Temperature: −10 °C to +50 °C
Dimensions: 483 × 43.8 × 349 mm (L × H × D)
Weight: Approximately 4.5 kg