MATFCCMMCCMM

Four Coaxial and Four Optical Modules
Combine coaxial antenna feeds and multiplexed single-mode fiber links in one RF distribution system.

Programmable Diversity Matrix
Route eight zones into four outputs or configure two independent groups of four zones feeding two outputs each.

Wideband RF Operation
Support RF distribution across a broad frequency range for varied installation requirements.

Integrated Spectrum Analyzer
Inspect individual input modules before adding them to combined signals, or monitor the combined signals directly.

Independent Diversity-Path Gain
Adjust A and B gain separately on each input module to balance incoming RF levels.

Multiplexed Optical Inputs
M2-equipped optical modules provide SC/APC connectivity using two optical wavelengths over single-mode fiber.

Remote Smart Antenna Control
Adjust gain and filtering on compatible Wisycom LFA, ADFA and BFA antennas through the coaxial modules.

Configurable Antenna Booster Power
Power antenna boosters through coaxial connections, with software-selectable High Boost operation available on up to two coaxial modules.

Local Touchscreen Configuration
Access settings through a large colour touchscreen, supported by buttons and an encoder.

Ethernet Remote Management
Manage the matrix remotely through its Ethernet interface.

AC and DC Supply Options
Integrate the matrix into installations using AC or DC power.

Configuration
Device Type: RF-over-fiber programmable matrix/combiner
Installed Coaxial Input Modules: 4, slots 1, 2, 5 and 6
Installed Optical Input Modules: 4 with M2 multiplexers, slots 3, 4, 7 and 8
Maximum Optical Modules Supported by Frame: 6
Diversity Zones: Up to 8
Matrix Modes: 8 zones into 4 outputs, or dual 4 zones into 2 outputs
Fiber Requirement: Single-mode fiber for all optical links

RF Performance
Frequency Range: 170 MHz to 1260 MHz
Input Gain: −25 to +3 dB
Gain Adjustment Steps: 0.5 dB
Gain Regulation: Independent for each input module, A and B separately
Coaxial Module OIP3: +22 dBm typical at 3 dB gain
Optical Module OIP3: +18 dBm typical at 3 dB gain
Coaxial Amplifier Linearity: ±1 dB typical
Coaxial Module Noise Figure: 6 dB typical at 3 dB gain
Optical Module Noise Figure: 15 dB typical at 3 dB gain

Coaxial Connections and Antenna Power
Input Connectors per Coaxial Module: 2 × BNC female, A and B
Coaxial Impedance: 50 Ω
Output Connector Type: BNC female, 50 Ω
Maximum Coaxial RF Input Level: −10 dBm, with overload alarm
Antenna Booster Power: +12 V DC / 220 mA
High Boost Antenna Power: +12 V DC / 400 mA
High Boost Availability: Maximum 2 coaxial modules, software configurable
Smart Antenna Control: Gain and filter control for Wisycom LFA, ADFA and BFA through coaxial modules

Optical Connections and Performance
Connector per Installed Optical Module: SC/APC
Optical Wavelengths: 1510 nm and 1550 nm
Optical Input Level: −6 dBm to +6 dBm (0.25 mW to 4 mW)
Absolute Maximum Optical Input Power: 10 mW; must not be exceeded

Spectrum Analyzer
Frequency Ranges: 170–260 MHz and 460–1260 MHz
Input Selection: Any one of the 8 input modules or combined signals, software selectable
Frequency Resolution: 50 kHz
Input Attenuator: 0 dB, 10 dB or 20 dB, software selectable
Timebase Accuracy: ±2.5 ppm maximum, 0–50 °C
Displayed Noise Level: −112 dBm typical
Displayed Amplitude Range: −117 dBm to −17 dBm
Maximum Input Level: −7 dBm with 20 dB input attenuation
Amplitude Accuracy: ±1.5 dB typical
Input IIP3: +15 dBm typical with 0 dB input attenuation
Sweep Speed: 70 MHz/s with diversity inputs
Full-Range Sweep Time: 13 seconds

Control and Display
Local Controls: Touchscreen menu, 2 buttons and encoder
Remote Interface: Ethernet 10/100 BaseT
Display Resolution: 1424 × 280 pixels
Display Colours: 16.7 million
USB Port: Reserved for future use

Power
AC Supply: 85–264 V AC, 47–63 Hz, 150 W maximum
Fuse: T3.15A
DC Supply: 10–28 V DC, 150 W maximum

Environmental and Physical
Operating Temperature: −10 °C to +50 °C
Dimensions: 483 × 43.8 × 349 mm (L × H × D)
Weight: Approximately 4.5 kg