MPN #5006A    
DPA 5006A

$15440.00

Financing available
Free shipping in Canada. Conditions

d:mension Surround Kit with 5 x 4006A, Clips, Windscreens in Peli Case



The DPA 5006A is a complete DPA 4006A Surround Kit with five carefully factory-matched omni microphones. Even though the standard tolerances on DPA Reference Standards are extremely low, the surround match is even closer.

The specially selected DPA 4006A microphones are matched within ±0.5 dB on both frequency response and sensitivity from mean of set. The maximum phase response difference is 5°.

The natural sound, high sensitivity, low noise-floor and extremely linear frequency response from 10 Hz to 20 kHz (±2 dB) of the microphones make the DPA 4006As the perfect choice for all AB Stereo, Decca Tree or surround main array recordings. The precise reproduction, total transparency and natural-sounding clarity of a DPA 4006A microphone will provide you with a lifetime of satisfying listening.

The foam design in the heavy-duty transportation box allows for fast and easy exchange of microphone/accessory.

Included in this kit
Carefully matched microphones, sturdy Peli case, holders, grids, and windscreens.
  • Wide pickup area and natural sound
  • Five carefully matched microphones
  • Ambience pickup with convenient directionality
  • Peli? Case transportation and protection
  • Directional pattern: Omnidirectional
  • Principle of operation: Pressure
  • Cartridge type: Pre-polarized condenser
  • Frequency range: 10 Hz - 20 kHz
  • Frequency range, ± 2 dB: 10 Hz - 20 kHz
  • Sensitivity, nominal, ± 2 dB at 250 Hz: 40 mV/Pa; -28 dB re. 1 V/Pa
  • Equivalent noise level, A-weighted: Typ. 15 dB(A) re. 20 µPa (maks. 17 dB(A))
  • Equivalent noise level, ITU-R BS.468-4: Typ. 27 dB (max. 29 dB)
  • S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL): Typ. 79 dB(A)
  • Total Harmonic Distortion (THD): < 1 % up to 139 dB SPL peak
  • Dynamic range: Typ. 124 dB
  • Max. SPL, peak before clipping: 147 dB
  • Switchable attenuator: 0 dB / -20 dB
  • Output impedance: < 200 ohm
  • Minimum load impedance: 2 kohm
  • Cable drive capability: 100 m (328 ft)
  • Output balance principle: Impedance balancing with Active Drive
  • Common Mode Rejection Ratio (CMRR): > 60 dB
  • Power supply (for full specifications): 48 V Phantom power (± 4 V)
  • Current consumption: 2.8 mA
  • Connector: XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phase
  • Color: Matte black
  • Weight: 163 g (5.7 oz)
  • Microphone diameter: 16 - 19 mm (0.6 - 0.75 in)
  • Capsule diameter: 16 mm (0.6 in)
  • Microphone length: 170 mm (6.7 in)
  • Output voltage, RMS: > 5 V
  • Polarity: +V at pin 2 for positive sound pressure
  • Temperature range: -40 °C to 50 °C (-40 °F to 122 °F)
  • Relative Humidity (RH): Up to 90%
  • Matching tolerance (freqency response, sensitivity): ± 0.5 dB
  • Phase deviation for kit: < 5°
  • View more products from DPA
    DPA Logo
    Now accepting
    Financing available
    Like us
    Follow us
    ©2004-2024 - Studio Economik Inc.® All Right Reserved.