Whenever a small, lightweight, inconspicuous microphone for top-quality recording is required, a d:dicate 4006C Microphone is the right choice.
Even though the standard tolerances on our d:dicate microphones are extremely low, a stereo match is even closer. These specially selected d:dicate 4006C microphones are matched within ±0.5 dB on both frequency response and sensitivity.
The pair comes in a heavy-duty Peli Case for safe transportation and easy access to the microphones and accessories.
The mic capsule
The MMC4006 Omnidirectional Microphone Capsule offers total transparency in any recording situation. It picks up incredible detail and depth of sound. The definition of its high-frequency characteristics across a wide range of instruments is impressive. It offers natural sound, high sensitivity, low noise-floor and extremely linear frequency response from 10 to 20 kHz (±2 dB).
A selection of accessories is available, including acoustic pressure equalizers, a nose cone and interchangeable protection grids. These accessories can acoustically transform the mic. By changing grids, it is possible to gain several unique frequency responses and directional characteristics from the mic. Furthermore, these accessories will not produce any phase shift, noise or distortion that would otherwise be introduced by an electrical filter.
A truly flexible range
The d:dicate 4006C Omnidirectional Microphone, Compact is part of the flexible d:dicate Microphones Series. It combines the MMC4006 Omnidirectional Capsule with the MMP-C compact preamplifier. This combination offers a subtle character alteration with a bit more "body" to the low end than the d:dicate 4006A Omnidirectional Microphone.
Another option, for the true audiophile, is the d:dicate 4006A Omnidirectional Microphone. It offers low distortion and totally accurate and faithful sound.
At any time, and with no tools needed, it is possible to transform the d:dicate 4006C Omnidirectional Microphone, Compact into a new configuration. You can combine it with another d:dicate or d:facto Microphone Capsule or Preamplifier.
The d:dicate 4006C Omnidirectional Microphone, Compact is also available individually.
Carefully matched microphonesNatural soundHigh sensitivityLow noise-floorExtremely linear frequencySturdy Peli Case for transportation and protection
Directional pattern: OmnidirectionalPrinciple of operation: PressureCartridge type: Pre-polarized condenserFrequency range: 10 Hz - 20 kHzFrequency range, ± 2 dB: 20 Hz - 20 kHzSensitivity, nominal, ± 2 dB at 250 Hz: 40 mV/Pa; -28 dB re. 1 V/PaEquivalent noise level, A-weighted: Typ. 15 dB(A) re. 20 µPa (max. 17 dB(A))Equivalent noise level, ITU-R BS.468-4: Typ. 27 dB (max. 29 dB)S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL): Typ. 79 dB(A)Total Harmonic Distortion (THD): < 1 % up to 134 dB SPL peakDynamic range: Typ. 119 dBMax. SPL, peak before clipping: 140 dBOutput impedance: < 200 ohmMinimum load impedance: 2 kohmCable drive capability: 100 m (328 ft)Output balance principle: Impedance balancing with Active DriveCommon Mode Rejection Ratio (CMRR): > 50 dBPower supply (for full specifications): 48 V Phantom power (± 4 V)Current consumption: 2.8 mAConnector: XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phaseColor: Matte blackWeight: 63 g (2.2 oz)Microphone diameter: 16 - 19 mm (0.6 - 0.75 in)Capsule diameter: 16 mm (0.6 in)Microphone length: 64 mm (2.5 in)Output voltage, RMS: > 4 VPolarity: +V at pin 2 for positive sound pressureTemperature range: -40 °C to 45 °C (-40 °F to 113 °F)Relative Humidity (RH): Up to 90%Matching tolerance: ± 0.5 dBPhase deviation for kit: < 5°
View more products from DPA