MPN #M2TND    
Lectrosonics M2TND

$3708.00

Financement disponible

The M2TND Digital Half-Rack Transmitter with analog audio inputs presents an excellent sounding IEM system with a unique level of performance in a wireless in-ear monitor system



With ultra-low latency 24-bit audio, digital RF modulation and two stereo digital channels, the M2T provides an unique IEM product for demanding, professional applications.

The M2T boasts a USB port for firmware updates and an IR port for fast setup. A large, high resolution, backlit LCD and large membrane switches provide an intuitive interface that is highly visible in daylight or dimly lit conditions.

The half-rack transmitter provides four analog audio inputs. The input connectors are full size XLR/TRS combo types for balanced line level analog signals. Input preamp circuits use a special balanced amplifier with very high common mode rejection to minimize hum and noise. Analog signals are converted to an internal 24-bit digital format which is then encoded, organized into packets, and passed to an RF modulator. The modulated RF signal is filtered before and after amplification to suppress out-of-band noise and spurious signals.

Conventional in-ear wireless monitor systems rely on decades-old technology: FM transmission with multiplexed, companded audio. The M2T Transmitter employs unique technology to provide ruler-flat frequency response from 20 Hz to 15 kHz and maximum channel separation. In addition, the digital audio eliminates a compandor and the associated artifacts. The result is crystal clear sound, rock solid stereo imaging, and extremely low distortion of <0.05%.

The M2T is designed and developed with the professional touring, installation, theater and broadcast customers in mind. The transmitter chassis is all-metal. The front panel is an aluminum extrusion with a durable powder coat finish.

The M2T half-rack transmitter features transmission power of up to 50 mW for extended operating range. Locking XLR connectors facilitate up to four channels of analog audio sources to be applied to the transmitter. A large, high resolution, backlit LCD and large membrane switches provide an intuitive interface.

Firmware updates are made via the USB port on the front panel of the housing. The procedure is very simple using a menu item on the transmitter and a standard micro USB cable connected to a PC.

Setup and adjustment are enabled through a backlit LCD, membrane switches and an intuitive menu structure. Input gain is adjustable over a wide range in 1 dB steps to optimize modulation and limiting for maximum signal to noise ratio and minimum distortion.
  • IEM (Wireless Monitor) with digital RF transmission
  • 24-bit digital audio
  • 2 independent stereo audio transmissions per 1/2 RV enclosure
  • USB port for firmware updates
  • IR (infrared) port for fast setup
  • Up to 50 mW per Rf carrier
  • Solid machined aluminum housing
  • RF Power Output: 2 RF carriers, 25 mW, 50 mW; adjustable.
    Antenna Output: 2 x BNC sockets
    Operating Frequencies: 470.1 - 607.975 MHz
    Frequency Selection Steps: 25 kHz
    Frequency Stability: ± 0.002%
    Modulation: 8 PSK
    Emission Designator: 200KG7E
    Spurious Radiation: >90 dB below carrier
    Equivalent Input Noise: -128 dBV
    Audio Frequency Response: 20 HZ - 15 KHZ +/- 1 dB
    Audio Input: -10 dBv or +4 dBu settings w/ ±5 dB trim
    Audio Input Jack: 4 x combo XLR/TRS connectors
    Ethernet Connection: RJ45
    USB Connection: Micro USB on front panel for firmware updates
    IRDA: IR transceiver for sync of receivers
    Input Impedance: Line, 2k Ohm
    Power Requirements: 9-18V DC
    Power Consumption: 5 Watts
    Dimensions: 1.75" x 8.375" x 7.75" (44.45 x 212.7 x 196.8 mm)
    Voir plus de produits pour la marque Lectrosonics
    Lectrosonics Logo
    Maintenant offert
    Financement disponible
    Aimez-nous
    Suivez-nous
    ©2004-2024 - Studio Economik Inc.® Tous droits réservés.